Skip to content

Description

The Ideal Clima Smart Detector R290 sensor (code CQGW01) detects R290 refrigerant gas leaks on Polo heat pump models Polo 10 K and Polo 12 K, but not on the Polo 8K Cooling Only. It detects gas from 500 ppm, which is 40 times below the lower flammability limit (LFL) set by the standard for R290, and allows Polo to be installed in particularly confined spaces.

High sensitivity and fast response to R290 gas

The sensor is calibrated to detect any refrigerant gas leak from 500 ppm, with high sensitivity and fast response. When a leak is present the LED flashes and an audible alarm repeats at regular intervals.

Automatic safety shutdown of Polo

When a leak is detected, the sensor activates the safety procedure: Polo's compressor switches off and, for 5 minutes, the indoor space is ventilated at maximum speed. The fan towards the outdoor side switches on cyclically to quickly eliminate any trace of refrigerant gas. During this period Polo cannot be switched off.

Factory calibration, no recalibration needed

The sensor is factory calibrated and self-calibrating, so it does not need recalibrating. During monitoring the green LED simply stays on.

Tin oxide sensor with power consumption below 750mW

The sensor incorporates a heating element and a gas-sensitive layer of tin oxide (SnO₂). It operates at 5V, with consumption below 750mW, and offers long-term stability.

Low sensitivity to alcohol, smoke and cooking fumes

The sensor has low sensitivity to alcohol, smoke and cooking fumes, which reduces false alarms.

Installation under Polo with RS485 cable included

The sensor is glued under the Polo air conditioner with the adhesive element, at the lowest point, for example on the underside. It has a plastic casing and connects to Polo's main board with an RS485 cable, included in the package.

Technical drawing of an oval capsule-shaped sensor with millimetre dimensions of length, width and depth

Compliance with standard CEI EN IEC 60335-2-40:2024+A1:2024

The sensor helps you meet the requirements of standard CEI EN IEC 60335-2-40:2024+A1:2024 and allows you to install Polo in particularly confined spaces, as shown in the table below.

Table with the installation square metres for the floor-standing and wall-mounted air conditioner, with and without R290 sensor

Table with the technical specifications of the R290 gas sensor: voltage, detection range, preheating time

Frequently asked questions

Which Polo models is the Smart Detector R290 sensor compatible with?
The Ideal Clima Smart Detector R290 sensor is compatible with the Polo 10 K and Polo 12 K heat pump models. It is not compatible with the Polo 8K Cooling Only.
At what R290 concentration does the Smart Detector R290 sensor detect a leak?
The Ideal Clima Smart Detector R290 sensor detects any refrigerant gas leak from 500 ppm, which is 40 times below the lower flammability limit (LFL) defined by the standard for R290.
What does the Smart Detector R290 sensor do when it detects a leak?
The Ideal Clima Smart Detector R290 sensor makes the LED flash, sounds an audible alarm and switches off the Polo compressor. For 5 minutes it ventilates the indoor space at maximum speed, and during this period Polo cannot be switched off.
Where should the Smart Detector R290 sensor be mounted on the Polo?
The Ideal Clima Smart Detector R290 sensor should be glued with the adhesive element at the lowest point of the Polo, for example on the underside.
Does the Smart Detector R290 sensor need recalibrating?
No, the Ideal Clima Smart Detector R290 sensor is factory calibrated and self-calibrating, so it does not require recalibration.
Does the Smart Detector R290 sensor trigger from alcohol, smoke or cooking fumes?
The Ideal Clima Smart Detector R290 sensor has low sensitivity to alcohol, smoke and cooking fumes, which reduces false alarms.

Technical specifications

Product codeCQGW01
BrandIdeal Clima
Gas detectedR290
Detection threshold500 ppm
Compatible modelsPolo 10 K and Polo 12 K (heat pump)
Not compatible withPolo 8K Cooling Only
Sensing elementtin oxide (SnO₂)
Power supply5V
Consumptionbelow 750mW
Indicatorsstatus LED and audible alarm
ConnectionRS485 cable included in the package
Casingplastic with adhesive element
Calibrationat the factory, self-calibrating
Positioninglowest point of the Polo, for example the underside